A Guide to Your First Paracord Bracelet
TL;DR: Your first paracord bracelet takes about 10 feet of 550 paracord, a buckle, scissors, a lighter, and a ruler. Measure your wrist and set the bracelet 1" longer than that number. Tie cobra knots down the full length. Trim the cord 1/4" from the last knot, then melt and press the ends so they hold.
Weaving your first paracord bracelet is the fastest way to learn the craft. It uses one main knot, one buckle, and one length of cord. This guide covers every step, from measuring your wrist to sealing the last cord end and beyond.
The pattern here is the cobra weave. You may also see it called the Solomon bar or the square knot bracelet. Learn it once and you will use it again and again in lanyards, keychains, slings, and wraps.

What do you need to make your first paracord bracelet?
You need just five things:
- At least 10 feet of 550 paracord, one color
- 3/8" side release buckle
- Scissors
- Lighter
- Ruler or measuring tape
How do you size a paracord bracelet?
Wrap a piece of paracord or a soft measuring tape around your wrist. Mark the spot where the end meets the rest of the cord. Lay it flat against a ruler and read the length. Add 1" to the measurement and you have your bracelet size.
Why add 1" to your wrist measurement?
The extra inch gives you room to move. It also makes up for the weave itself. A paracord bracelet is thick, and that thickness eats into the inside diameter.
The bracelet length is measured from one buckle end to the other. Do not count the buckle teeth. You will set this length during setup, before you tie a single knot.
What if your bracelet comes out too big?
Soak it in water and let it air dry. Nylon shrinks about 1/4" this way. More than that, and it is faster to just retie.

How do you pick colors for a paracord bracelet?
Use one solid color for your first bracelet. It keeps your attention on the knot. Once the weave feels natural, try two colors with strong contrast.
The right color pairing can carry a simple design. Our guide to paracord color combinations walks through what works.
How to make a basic cobra weave bracelet
Set the length on the buckle first. Then tie alternating knots down the bracelet until there is no room left. Setup takes 4 steps, and the weave is one knot repeated.
- Fold your 10 feet of paracord in half. Push the folded end through the slot on one buckle half, from the top.
- Open the loop and pull it back over the buckle. Tighten it down. This lark's head knot (cow hitch) anchors the cord and creates the two center strands your knots wrap around.
- Keep the two cords side by side with no twist. Feed both loose ends through the slot on the other buckle half, from the top. Pull them through.
- Measure from one buckle end to the other, not counting the teeth. Slide the cord until that distance equals your wrist plus 1".
- Lay the bracelet flat. Put one working end on each side of the two center strands.
- Cross the left cord over the center strands. Leave a loop on the left side.
- Bring the right cord down over the top of the left cord.
- Pass the right cord behind the center strands.
- Bring it up through the left loop.
- Hold the cord where it exits the buckle. Pull the knot tight right under the buckle. Check that the length has not changed.
- Tie the same knot mirrored. Right cord across the top, left cord over it, then behind and up through the right loop. Tighten. Repeat Steps 6 to 11 down the full length.
- Keep alternating left, right, left, right down the bracelet. Every few knots, slide them up toward the buckle to keep the weave tight.
- When no more knots fit, cut both working cords 1/4" from the bracelet.
- Melt each cut end with a lighter. Place flame near but not directly on the ends. Within about 3 seconds, press it flat with the side of your scissors.
Prefer to watch? Follow the video version of this tutorial or check out our photo tutorial.

What are the most common first paracord bracelet mistakes?
Most first-bracelet problems come from sizing, skipped alternation, or too much heat. Each one has a quick fix.
|
Problem |
Cause |
Fix |
|---|---|---|
|
Bracelet is too tight |
Wrist measured without the extra 1" |
Retie with the buckle set to wrist plus 1". |
|
Bracelet is slightly too loose |
Length set long during setup |
Soak in water and air dry. It shrinks about 1/4". |
|
Knot doesn't look right |
Same side tied twice in a row |
Untie back to the last matching knot. Alternate left and right. |
|
Gaps between knots |
Knots not pushed together |
Slide knots up toward the buckle every few knots. |
|
Center strands crossed |
Cords twisted during setup |
Keep both cords side by side before feeding the second buckle half. |
|
Ends turn black and crusty |
Cord held in the flame |
Hold the end beside the flame. Melt, don't burn. |
|
End pulls back through the last knot |
Melted tip not pressed flat in time |
Press within about 3 seconds of melting. |
How do you fuse Paracord strands for two-color bracelets?
- Cut both cords square with sharp scissors. A clean, flat cut fuses straighter than a frayed one.
- Pull out a half inch of inner strands from both cords and cut.
- Melt both ends at the same time, just beside the lighter flame. Stop when the tips turn glossy and soft. If either end turns black, cut it off and start again.
- Press the melted ends together right away, end to end and lined up straight. Hold steady for about 10 seconds while the nylon sets.
- While the seam is warm but no longer liquid, roll the seam between your fingers to secure. Never touch molten nylon with your fingers.
- Let the seam cool fully, then give it a firm tug. If it separates, cut off the seam and repeat steps 1 to 5.
For a two-color cobra bracelet, fuse two 5-foot lengths and use the seam as the fold in step 1 of the tutorial above. The seam sits inside the lark's head on the buckle, and each working end comes out a different color.
Which knots should you practice after the cobra knot?
Start with the knots that show up in almost every project. Most complex knots are combinations of these.
- Square knot: the core of the cobra weave
- Lark's head (cow hitch): attaches cord to a buckle, ring, or carabiner
- Snake knot
- Diamond knot
- Barrel knot
- 3-strand braid
Your first bracelet uses two of them: the lark's head and the square knot. For the rest, work through our printable photo tutorials.
What should you make after your first paracord bracelet?
Use the same cobra weave on a new project. You already know the knot. Only the length and the hardware change.
- Keychain fob: a short cobra weave on a split ring.
- Dog collar: a longer cobra weave on a wider buckle.
- A new weave: try a two-color bracelet or a new pattern from the Paracord Planet YouTube channel.
Ready to tie your first bracelet?
Shop 550 Paracord | Shop Bracelet Kits
Want the next tutorial when it drops? Sign up for Paracord Planet emails.